Boating New Zealand Boat Reviews
Reviews
Boating New Zealand News
News
Boating New Zealand Sports
Sport
Boating New Zealand Lifestyle
Lifestyle
BOAT-REVIEWS-MOBILE
Boat Reviews
BOAT-NEWS-MOBILE
News
BOAT-SPORTS-MOBILE
Sports
BOAT-LIFESTYLE-MOBILE
Lifestyle
HomeBoatBoat MaintenanceLeaking hydraulic steering

Leaking hydraulic steering

Bookmark post
Bookmarked
Bookmark post
Bookmarked

Steering leaks are messy and can result in the total loss of steering control, writes Norman Holtzhausen.

In this column last year, we covered the types of steering systems commonly used in boats, including the ubiquitous hydraulic system. Hydraulic steering systems are efficient, reliable and relatively low maintenance. An annual check of the hydraulic fluid is usually all that is needed to keep everything in good working order – until the system does not work anymore.
Well… actually, hydraulic steering usually gives an indication all is not well before it fails completely. The most common symptom is excessive ‘play’, where the wheel can be turned in either direction for a fair way before the outboard, drive or rudder actually starts to turn. The other common symptom is a shuddering as the steering is turned hard, as if the system is grabbing, then releasing, then grabbing again. Both are caused by insufficient hydraulic pressure between the helm pump and the steering piston.

Steering unit removed from the boat.

The first course of action is always to top-up the fluid level at the helm filler plug, using the approved hydraulic fluid. If you have not done this for a long time and fluid levels have become low, it may completely solve your problem. But if you have topped up recently and the level is still low, you have a leak somewhere. We discovered this problem just before Christmas – not the greatest time to have a mechanical problem with your boat!
Hydraulic leaks only need to be very tiny to cause a problem. Because the pressure in the system is often over 100PSI/6.90 Bar – roughly three times the pressure in your car’s tyres –even a pinhole-sized leak can cause fluid to rapidly escape. The most common causes of leaks are perished and broken hoses or worn and leaking seals.

There are two seals inside each end cap.

On most systems the hoses do not flex when the steering is turned, as the steering cylinder is attached to the engine mount and the piston rotates the body of the engine. On other models, the piston is fixed and the cylinder moves to shift the engine, causing repeated hose flex. In both cases, however, tilting an outboard produces some twisting or flexing of the hoses. That’s why the spot where the hydraulic hose attaches to the cylinder takes the most wear.
This repeated bending and straightening can result in hose failure, and in that case, there is no option but to replace the entire hose. Hose failure is most likely to cause complete and sudden steering failure, although if you are ‘lucky’ you may get some indication it is starting to leak before it ruptures completely.
In our case, though, the leak was slightly more subtle. We had topped up the steering fluid only about two months ago but once again we experienced a shuddering when turning under load. Checking the level showed that it was again too low, which clearly indicated a leak. Using a clean white paper towel, we carefully wiped underneath each of the hose connections to find any oil, to no avail. So, it was not a hose or connection problem.

Using the tool to remove the end caps.

Repeating this paper towel wipe at the bottom of the helm pump also came clean.
But the steering cylinder attached to the outboard was a different story. Although there was no visible evidence of a leak, a fingertip wiped under the shaft end of the cylinder came up wet with hydraulic fluid. One of those seals was worn and leaking! Because the cylinder sits over the water, the drips had gone unnoticed. A strip down and replacement was needed.


This procedure is one of those DIY jobs that needs to be tackled with caution. The inside of any hydraulic system needs to be kept absolutely clean – it is not a beachside repair job. Indeed, if you don’t have a proper workshop, bite the bullet and get the professionals to service the cylinder. However, if you are confident and have the facilities, then the job is not particularly difficult.
First on the agenda: source the correct replacement kit for your specific model cylinder. Since this happened the week before Christmas, I was not confident of getting it sorted in a hurry. The parts had to be couriered from the suppliers who were out of town, but in a minor “miracle before Christmas” it duly arrived on the 24th of December. A few days later, once we had all recovered from Christmas hangovers, it was time to tackle the job. I removed the cylinder from the boat, carefully sealing off the end of the disconnected hoses to prevent any contamination.

9. Reassembling the end caps. Note how well the cardboard contains everything.

Back in the workshop the work surface was covered with a single large sheet of clean corrugated cardboard. This serves several purposes: it is a clean, dust-free surface, it rapidly absorbs any spilled hydraulic fluid, and it is easy to see the parts laid on it.
I started by opening the kit and fully reading the instructions (yes, I do read the manual first!). Then I laid the parts out on the cardboard in the order I thought I would need them.
Removing the end caps from the cylinder was easy using the tool provided in the kit, and I carefully pulled out the whole piston shaft assembly. A clean rag was used to wipe off the excess hydraulic fluid and the main piston seal with its supporting collars were quickly replaced.
As the old parts were removed from my arranged sequence they were placed in a small pile at the corner of the cardboard. This way, by the end of the job there should be no unused parts still laid out and I would be confident I had replaced everything.
One of the end caps contained two different seals, one an O-ring and the other a stiff oil scraper. A hooked sewing pin was the easiest way to extract these from their slots in the end cap, and the new ones were eased back into place. Note that wetting the seals with clean hydraulic fluid helps with fitting them. Once all the parts were installed, it was easy to reassemble the cylinder, again with the assistance of plenty of clean fluid to lubricate the seals.

The new seals in place.

After confirming that all the new parts had been fitted (in other words, no parts left on the cardboard!) I then checked the motion of the piston in the shaft. Everything was operating smoothly, so I tightened up the end caps as per the instruction sheet. Time to fit it back onto the boat, and since bleeding the system really is a two-man job, I called on my buddy to come and assist.
The kit came with a small tube of Locktite, to be used on the bolts holding the cylinder to the engine frame. This was duly applied and the bolts tightened up. The piston was fully pushed to the left of its range of motion, the hydraulic hoses were attached, and a transparent plastic tube attached to the bleed nipples on each of the cylinder’s hose attachments. The open ends of those tubes were put into a clean receptacle and the nipples were opened.

Job done.

Now we needed to pump fluid and eliminate air bubbles from the hose. Using a funnel, firmly fitted to the helm pump filler hole, we topped up the fluid. We turned the steering to the right (opposite to where we had located the piston) and continued to turn that way until no air bubbles were visible in the bleed tube. We then closed that bleed nipple and continued to turn the helm to the right, causing the cylinder to now fill with fluid and move across to the other side.
The opposing bleed tube allowed the air from inside the cylinder to escape. Once the piston was fully to the right, we then carefully started turning the steering back again to the left. Initially more air, then fluid with bubbles, came out of that bleed tube. Again, once we had no bubbles, we closed the nipple. Now we could operate the steering forcefully, lock-to-lock in both directions. We did this a couple of times.

Fitting plastic tube to the bleeding nipple.

If the steering is still ‘spongy’ it indicates there are still small bubbles trapped in the system. The ideal is that it should be hard, with almost no play when swinging from left to right. If necessary, turn lock-to-lock half a dozen times then repeat the bleed process.
In our case we managed to avoid any major bubbles and there was no play or sponginess. We ensured the fluid level in the helm pump was at the recommended level, then removed the funnel and replaced the filler plug. Job done!

Using a funnel in the helm filler hole to top up the fluid.

Actual time required was less than two hours, although having to take the cylinder off and then later in the day arrange a helper to bleed the system meant it took up more than half a day. The cost was $175 for the kit and $25 for a new bottle of hydraulic fluid. Plus, we were soon back out on the water at a time of year when getting it sorted by a professional would have been a very hard ask.

SHARE:

Related Articles

Comments

This conversation is moderated by Boating New Zealand. Subscribe to view comments and join the conversation. Choose your plan →

This conversation is moderated by Boating New Zealand.

Boating New Zealand
Boating New Zealandhttps://www.boatingnz.co.nz
Boating NZ is New Zealand’s premier marine title devoted to putting its readers behind the wheel of the latest trailerboats, yachts and launches to hit the market. It inspires with practical content and cruising adventures, leads the fleet with its racing coverage and is on the pulse of the latest maritime news and innovation.

More from Boating New Zealand

The 45th Rolex Middle Sea Race...

For more than four decades, the Rolex Middle Sea Race has brought the world...
Middle Sea RaceNewsRolex

Tūtaia Launched: Waikato Regio...

Replacing An Old Workhorse: Farewell to Maroro For 17 years, Maror...
Boat BriefBoating NewsNews

Raising The Spar: New Standard...

Emirates Team New Zealand’s Triumph: A Legacy In The Making Emirat...
AC37America's CupBoat Brief

Interim Factual Report on the ...

Incident Overview and TAIC’s Inquiry Process In the weeks leading ...
BoatFeaturesNews

Thrills and Precision at the J...

The Jet Boating NZ Mitre 10 National Rally 2024 on October 27 brought energ...
Mitre 10 National Rally 2024News

Dockside Glimpses: An Inside L...

A Walk Along the Docks Our guide, Kiwi skipper Conrad Colman, lead...
Introduction and Warm UpNewsSport

Follow Us

Weekly Newsletter

Stay up to date with the latest developments shaping New Zealand's Boating world.

Social Media

Follow us on social media to stay in the loop with the latest trends and news shaping New Zealand's boating scene!

HOT OFF THE PRESS

The 45th Rolex Middle Sea Race – A Test of Skill and Spirit

For more than four decades, the Rolex Middle Sea Race has brought the world’s top sailors to Malta’s...
Middle Sea RaceNewsRolex

Tūtaia Launched: Waikato Regional Council’s New Vessel Ready For Action

Replacing An Old Workhorse: Farewell to Maroro For 17 years, Maroro has been the backbone o...
Boat BriefBoating NewsNews

Raising The Spar: New Standards Set In Historic 37th America’s Cup

Emirates Team New Zealand’s Triumph: A Legacy In The Making Emirates Team New Zealand’s imp...
AC37America's CupBoat Brief

Interim Factual Report on the Aratere Grounding: Navigational Oversights, Technical Challenges, and ...

Incident Overview and TAIC’s Inquiry Process In the weeks leading up to the incident, Arate...
BoatFeaturesNews

Thrills and Precision at the Jet Boating NZ Mitre 10 National Rally 2024

The Jet Boating NZ Mitre 10 National Rally 2024 on October 27 brought energy and excitement to the c...
Mitre 10 National Rally 2024News

Events Worth Adding to Your Calendar

Have an event you'd like to list on Boating New Zealand. Contact us with the details.

Catch all the action of the Louis Vuitton 37th America's Cup, happening from 22 Aug to 27 Oct 2024 in Barcelona, Spain. Follow along with excitement at Boating New Zealand.

FISHING

Stabicraft Te Anau Manapouri Fishing Classic, 25 - 27 Nov 2024 in Te Anau Manapouri

Extreme Boats Fishing Tournament, 29 & 30 Nov 2024 in Whitianga

NZ Lure Masters (Catch, Measure and Release competition), 3 & 4 Oct 2025, New Zealand wide

REGATTAS

NZ Match Racing Championships, 14 - 17 Nov 2024 in Auckland

Beneteau Owners Rally, 23 Nov 2024, Auckland to Kawau

Sir Peter Blake Torbay Regatta, 30 Nov - 1 Dec 2024 at Torbay Sailing Club

Rolex Sydney to Hobart, 26 Dec 2024 starts in Sydney, Australia

New Zealand Sail Grand Prix, 18 & 19 Jan 2025 in Auckland

NZ Millenium Cup, 1 - 4 Feb 2025 at Waitemata Harbour

Toyota Youth International Match Racing Cup, 26 Feb - 4 Mar 2025 in Auckland

PIC Insurance Brokers Coastal Classic, 24 Oct 2025 TBC from Auckland to Russell

JET BOAT RACING

UIM World Jetsprint Championships, 25 Jan -2 Feb 2025 at Wanaka (25 & 26 Jan) and Wanganui (1 & 2 Feb)

2024 Golden Homes NZ Jet Boat Marathon, 2025 dates TBC on Southland Rivers (Oreti, Waiau and Mataura)

National Jet Boat Rally 2024, 2025 date TBC at Oliver Road, Bendigo (near Cromwell)

WATERSPORTS

Yamaha Rollo's Marine Bridge 2 Bridge, 8 - 10 Nov 2024 Staged on the Waikato River between Cambridge & Taupiri, based in Hamilton, New Zealand

NON-MOTORISED SPORT

Waka Ama - 2025 National Sprint Championships, 12 - 18 Jan 2025 at Lake Karapiro, Cambridge

Waka Ama - 2025 Secondary School Nationals, 24 - 28 Mar 2025 at Lake Tikitapu, Rotorua

COMMUNITY

NZ Retro Boats Lake Tarawera Gathering, 16 Nov 2024 at Hot Water Beach, Lake Tarawera, Rotorua

Bay of Islands Cruiser's Festival, 20 - 23 Nov 2024 at Bay of Islands Marina, Opua

The New Zealand Sailing Trust 5 Day Sail, 13 - 17 Jan 2025 starting in Auckland

Auckland Boat Show, 6 - 9 March 2025 at Viaduct Events Centre and Jellicoe Harbour, Auckland

The Hutchwilco New Zealand Boat Show, 15 - 18 May 2025 at Auckland Showgrounds, Auckland

Lake Brunner Classic Boats Get Together, TBC Oct 2025 at Moana

Whangārei Maritime Festival, TBC Oct 2025 at the Whangārei Town Basin

ADVENTURES AT SEA

The Norwoods World Tour

Stone Town, Zanzibar Aug 2024

This is the (liberal) English translation of an old Norwegian classic. And annoyingly, this ear-worm...
Features

Gods And Goats, Not All What They’re Hyped Up To Be

I’m not privy to the details of what my sister said in her prayer to Thor with regards to the weathe...
The Norwoods World Tour

When A Series Of Unfortunate Events Force An Unexpected U-Turn

Saturday a week ago we went to drop off a rental car we had hired to take my sister back to the airp...
One Family’s Boating Journey

One Family’s Boating Journey; That sinking feeling

What a shocking end to our summer! We never saw this plot twister coming!
One Family’s Boating Journey

One Family’s Boating Journey: Life lessons

As our two boys, Rafe and Chris, have discovered when you’re living onboard, life will throw you cur...

NEWS TIPS?
Send your photos, videos, stories, and tip-offs to ahoy@boatingnz.co.nz or call us on 022-023-7507.

BOATS FOR SALE