Boating New Zealand Boat Reviews
Reviews
Boating New Zealand News
News
Boating New Zealand Sports
Sport
Boating New Zealand Lifestyle
Lifestyle
BOAT-REVIEWS-MOBILE
Boat Reviews
BOAT-NEWS-MOBILE
News
BOAT-SPORTS-MOBILE
Sports
BOAT-LIFESTYLE-MOBILE
Lifestyle

The back end

Bookmark post
Bookmarked
Bookmark post
Bookmarked

PLUMBING A TOILET AND HOLDING TANK

Any boat that is going to be used for extended trips will need a toilet of some sort.

For very occasional use, a bucket is the cheapest option, and Burnsco sells a toilet bucket with a suitably shaped seat. The next step up is a chemical toilet, and there is a range of those with removable ‘cassettes’ that make them easier to empty. But there is nothing like the convenience of a proper flush toilet.

Flush tiolets start at just over $300 for a manual flush with a hand pump and around $450 for the most basic electric flush model. A macerator pump takes care of the waste, cutting it into extremely fine pieces which can then be flushed out into the surrounding water.

Of course, there are rules about when and where you can flush human waste directly into the sea. You must be in water deeper than five metres and more than 500m from the nearest shore or marine farm if you want to flush untreated waste. For most places in New Zealand that means that you cannot flush the toilet directly overboard while in a sheltered anchorage, and most popular fishing spots also fall within the restricted range.

There are two solutions to this problem. The simplest is to install a holding tank. This will temporarily hold the waste on board, and the tank can then be flushed out either when you are far enough from shore, or at the marina’s pump-out facility.

The second option is more environmentally friendly but also more expensive: fitting a sewage treatment system to your boat. Until recently these treatment systems were only practical for relatively large vessels, due to their size and cost. However, they have steadily become cheaper and more compact. There are now a couple of options.

2. The solenoid-operated valves. Note they also have a manual override system.
3. The shower area ready for the toilet installation.

The Raritan Electro Scan is readily available in New Zealand from Lusty & Blundell and costs just over $5000 for the basic unit. Using salt water and 12Vpower, it generates powerful bactericides inside the unit and treats the waste in a three-stage system. This enables the toilet to be used as and where it is needed, and the unit takes about the same space as a moderate sized holding tank.

For my boat Divecat, however, I already had an 80-litre holding tank from the original fitout. Being plastic, it was completely unharmed by its time under water and so I elected to install an electric flush toilet combined with that holding tank. There are numerous ways these can be plumbed together, but the simplest is to have the toilet outlet feed straight into the holding tank. The holding tank outlet then empties out to sea through a valve which can be closed when in a restricted area. An 80-litre capacity can cope with a dozen or more toilet operations before needing emptying.

I had already sourced and positioned my toilet, so just needed the appropriate plumbing items to connect everything up. However, I had introduced a new complication – the new toilet location is now below the waterline, whereas previously it was up at deck level. This creates the obvious risk that water can seep past the toilet’s internal seals and eventually overflow, flooding the toilet compartment and potentially even causing the boat to sink.

There are two items that can prevent this. The first are vented loops, something that I have previously installed on the bilge hoses. These contain a small release valve located on the top of a loop of hose that is positioned above the waterline. This valve allows a small amount of air to break the backward siphon action that could otherwise happen with a liquid-filled hose. As soon as there is positive water pressure inside the hose (as happens when the electric pump turns on, or the manual flush is operated), this small valve closes and the hose operates as required.

The second safety feature is a check valve that is closed when the toilet is not in use. During normal operation of the toilet the impeller in the macerator pump acts as a seal to prevent water flowing in, but these are not intended to prevent slow water ingress over a long period of time. Any extra check valve would need to be opened before flushing the toilet and closed again after use.

On many boats a standard part of the operating procedure is ensuring the toilet stop valves are closed as part of the shut-down procedure after a trip. Best practice has these valves located as close as possible to the through-hull fitting, so they can also be used if maintenance is needed on any part of the system.

The trouble that I was going to be facing was the location of the toilet and the through-hull fittings. There was very little space inside the shower/toilet compartment to locate a manual valve next to the toilet itself, and having one in the hull void would be extremely inconvenient. A solenoid-operated valve with a failsafe, normally closed mode was required. Fortunately, the hull void where these will be located is inside the main cabin area and so is well protected. This allows me to source solenoid valves that are commonly used by water irrigation systems, rather than requiring a more robust IPx68-rated system. And I will wire the inlet hose solenoid to the same switch as the flush mechanism – when someone uses the toilet and presses the flush switch, that valve will open, the toilet can flush, and the valve will then close again. Only the holding tank outlet valve will be separately controlled so the skipper can decide when and where to empty the holding tank.

4. Fitting the tank sender. Note the float on this style is fully encased to prevent solids from jamming it up.

On reflection, I decided I did not need both the solenoid valves and the vented loop. For the water inlet side, I would have needed a solenoid-activated vented loop since the air valve operates on positive pressure only. Unfortunately, the water pump on the toilet sucks the water and hence creates negative pressure in the water inlet hose. This means I would need to close the vent for the pump to work.

Solenoid-activated vented loops are readily available but are pricey, and I reasoned that another type of normally closed solenoid valve would provide adequate protection. On the outlet side, the top of the holding tank will be slightly above the waterline and has its own air vent. Hence it provides the equivalent level of protection as a vented loop. So, more stuff needed to be purchased. My final parts list was:

19mm through-hull fitting for water inlet 

19mm inside diameter hose for water inlet 

19mm solenoid valve for water inlet Electric toilet unit with controls (already purchased)

25mm waste hose for toilet outlet to connect into holding tank Holding tank (already on hand)

38mm waste hose for outlet from holding tank

38mm solenoid valve for waste 

38mm through-hull fitting 

13mm through-hull fitting for holding tank vent 

13mm hose for vent

5. The holding tank frame, plus the through-hulls all fitted.
6. And the holding tank fitted together with double-clamped hoses.

The holding tank also already had a manual ball-valve fitted directly to it, which I decided to retain as a backup valve. Since I also needed a separate control switch for the holding tank shutoff solenoid valve, I added a waste tank level gauge and integrated switch from Burnsco. This would let me see how full the tank is and let me operate the solenoid valve to empty it when it is possible to do so. Realistically this was the only time I would be able to add a tank-level sender to the holding tank – once a few bowel movements had been through the system I would not be cutting any openings into it!

Of special note is that you must use sanitation-grade hose and fittings. Normal PVC hose may allow odours to permeate through the hose wall – not a pleasant prospect. It is worth paying the premium for this hose and never having to worry about it again. The other safety feature is that all belowwaterline hoses should be double clamped, so that any failure in the hose clamp does not result in water leaking in.

The first photo shows all the equipment ready for installation. I had cut the hole in the holding tank for the sender unit and made use of the opening to fully clean the inside with a water blaster. Installation was a relatively straight forward job, although my muscles were aching by the end of it due to repeatedly climbing in and out of the hatch into the hull.

7. Toilet secured and plumbed in.
8. Last part of the toilet installation – the control switch, and of course, the wiring out the back of it.

The wiring took a bit longer since I needed to run power for the toilet, and then control cables for the waste solenoid and the tank sensor cables up to the helm. Finally, I could fit the gauge and switch into the dash. A few quick tests and I could confirm everything seemed to be connected. Since the boat is out on the hard, I got a friend to hold a running hose into the water inlet while I tested the flush mechanism and holding tank vent valve (with clean water only – not a real test, but best in case I did find a leak.) All done.

I had some of the components already on hand, particularly the holding tank. If I’d had to purchase everything new for this project the total cost would have been around $1500, based on my size holding tank. Smaller tanks are cheaper. And the job took about six hours to complete, excluding the time to locate the components needed. BNZ

SHARE:

Related Articles

Comments

This conversation is moderated by Boating New Zealand. Subscribe to view comments and join the conversation. Choose your plan →

Boating New Zealand
Boating New Zealandhttps://www.boatingnz.co.nz
Boating NZ is New Zealand’s premier marine title devoted to putting its readers behind the wheel of the latest trailerboats, yachts and launches to hit the market. It inspires with practical content and cruising adventures, leads the fleet with its racing coverage and is on the pulse of the latest maritime news and innovation.

More from Boating New Zealand

Bluebridge Ferry Incident: Str...

In a dramatic turn of events, Bluebridge’s Connemara ferry collided with Pi...
Boating NewsIncidents at SeaNews

Back to the Future: J Class Jo...

A New Age The AC75s of the America’s Cup deliver no shortage of jaw-dropp...
AC37Boat WorldSport

Coastguard Taranaki Earns Four...

Coastguard Taranaki’s unwavering dedication to maritime safety has been rec...
News Bites

AC37 Regatta: A Taste Of Thing...

The Louis Vuitton 37th America’s Cup officially started in sunny Barcelona ...
AC37FeaturesLouis Vuitton Cup

Sailing Away: The Brett Bakewe...

Bakewell-White’s boating story begins with his grandfather, the late Richar...
FeaturesOctober 2024Reflections

Exclusive offer celebrates new...

The first Dufour 44 in Asia Pacific will land in October, and The Yacht Sal...
2024Boat BusinessBoating News

ARE YOU STAYING CONNECTED WITH THE LATEST DEVELOPMENTS SHAPING NEW ZEALAND'S BOATING WORLD?

Join Our
Weekly Newsletter

HOT OFF THE PRESS

Bluebridge Ferry Incident: Strong Winds Cause Damage at Picton Wharf

In a dramatic turn of events, Bluebridge’s Connemara ferry collided with Picton's wharf during a ber...
Boating NewsIncidents at SeaNews

Back to the Future: J Class Joins AC75 & AC40 Fleets in Barcelona

A New Age The AC75s of the America’s Cup deliver no shortage of jaw-dropping action. And the AC40s...
AC37Boat WorldSport

Coastguard Taranaki Earns Four Nominations in 2024 Coastguard New Zealand Volunteer Awards

Coastguard Taranaki’s unwavering dedication to maritime safety has been recognised in a remarkable w...
News Bites

AC37 Regatta: A Taste Of Things To Come

The Louis Vuitton 37th America’s Cup officially started in sunny Barcelona with the third and final ...
AC37FeaturesLouis Vuitton Cup

Sailing Away: The Brett Bakewell-White Story

Bakewell-White’s boating story begins with his grandfather, the late Richard (Dick) Bakewell. A lif...
FeaturesOctober 2024Reflections

Events Worth Adding to Your Calendar

Have an event you'd like to list on Boating New Zealand. Contact us with the details.

Catch all the action of the Louis Vuitton 37th America's Cup, happening from 22 Aug to 27 Oct 2024 in Barcelona, Spain. Follow along with excitement at Boating New Zealand.

COMING EVENTS

Waka Ama - 2024 Long Distance Nationals, 3 - 6 Oct 2024 at Oneroa (Midway Beach) Gisborne

Lake Brunner Classic Boats Get Together, 11 - 13 Oct 2024 at Moana

Whangārei Maritime Festival, 12 - 13 Oct 2024 at the Whangārei Town Basin

2024 Golden Homes NZ Jet Boat Marathon, 22 - 26 Oct 2024 on Southland Rivers (Oreti, Waiau and Mataura)

National Jet Boat Rally 2024, 27 Oct 2024 at Oliver Road, Bendigo (near Cromwell)

Yamaha Rollo's Marine Bridge 2 Bridge, 8 - 10 Nov 2024 Staged on the Waikato River between Cambridge & Taupiri, based in Hamilton, New Zealand

NZ Match Racing Championships, 14 - 17 Nov 2024 in Auckland

Bay of Islands Cruiser's Festival, 20 - 23 Nov 2024 at Bay of Islands Marina, Opua

Extreme Boats Fishing Tournament, 29 & 30 Nov 2024 in Whitianga

Sir Peter Blake Torbay Regatta, 30 Nov - 1 Dec 2024 at Torbay Sailing Club

Rolex Sydney to Hobart, 26 Dec 2024 starts in Sydney, Australia

Waka Ama - 2025 National Sprint Championships, 12 - 18 Jan 2025 at Lake Karapiro, Cambridge

The New Zealand Sailing Trust 5 Day Sail, 13 - 17 Jan 2025 starting in Auckland

New Zealand Sail Grand Prix, 18 & 19 Jan 2025 in Auckland

UIM World Jetsprint Championships, 25 Jan -2 Feb 2025 at Wanaka (25 & 26 Jan) and Wanganui (1 & 2 Feb)

NZ Millenium Cup, 1 - 4 Feb 2025 at Waitemata Harbour

Toyota Youth International Match Racing Cup, 26 Feb - 4 Mar 2025 in Auckland

Waka Ama - 2025 Secondary School Nationals, 24 - 28 Mar 2025 at Lake Tikitapu, Rotorua

Auckland Boat Show, 6 - 9 March 2025 at Viaduct Events Centre and Jellicoe Harbour, Auckland

The Hutchwilco New Zealand Boat Show, 15 - 18 May 2025 at Auckland Showgrounds, Auckland

NZ Lure Masters (Catch, Measure and Release competition), 3 & 4 Oct 2025, New Zealand wide

ADVENTURES AT SEA

The Norwoods World Tour

Stone Town, Zanzibar Aug 2024

This is the (liberal) English translation of an old Norwegian classic. And annoyingly, this ear-worm...
Features

Gods And Goats, Not All What They’re Hyped Up To Be

I’m not privy to the details of what my sister said in her prayer to Thor with regards to the weathe...
The Norwoods World Tour

When A Series Of Unfortunate Events Force An Unexpected U-Turn

Saturday a week ago we went to drop off a rental car we had hired to take my sister back to the airp...
One Family’s Boating Journey

One Family’s Boating Journey; That sinking feeling

What a shocking end to our summer! We never saw this plot twister coming!
One Family’s Boating Journey

One Family’s Boating Journey: Life lessons

As our two boys, Rafe and Chris, have discovered when you’re living onboard, life will throw you cur...

NEWS TIPS?
Send your photos, videos, stories, and tip-offs to ahoy@boatingnz.co.nz or call us on 022-023-7507.

BOATS FOR SALE